Available NU2968-M1 Single-Row Cylindrical Roller Bearing

Available NU2968-M1 Single-Row Cylindrical Roller Bearing
Details:
-The Main dimension 340x460x72 mm;Weight:34.6 kg
-36 pieces are ex-stock to achieve fast delivery
-Drawings and datasheets could always be provided for your reference
-COO/CO(Certificate of Origin) will be provided
Send Inquiry
Description
Send Inquiry

NU2968-M1 With Size 340x460x72 mm Single-Row Cylindrical Roller Bearing

 

Overview

 

Single row non-locating cylindrical roller bearings,With brass cage, In series NU, the outer ring has two ribs, while the inner ring has no ribs.M1-Two Piece Brass Cage Roller Guided;Normal radial internal clearance.Running accuracy in P6.

Bore diameter-340 mm;Outside diameter-460 mm;Width-72 mm; Mass-34.6 kg;Cr=950 kN;C0r=1930 kN;Limiting speed=2400 1/min;Reference speed=950 1/min.


Extended similar type NU 2968 M; NU2968-M1-C4; NU2968 are also EX-stock for your more industrial solutions.

 

Specifications


NU2968-M1 bearing drawing
 

Dimensions &Technical Datasheets
Part NO. NU2968-M1 - Single-Row Cylindrical Roller Bearings
Brand FAG brand made in GERMANY/SDVV brand made in China
Main Dimensions 340x460x72 mm
d 340 mm
D 460 mm
B 72 mm
rmin 3 mm
Limiting speed 2400 1/min
Reference speed 950 1/min
da 352 mm
Da 448 mm
ra max. 2.5 mm
Cr 950 kN
C0r 1930 kN
M 34.6 kg

 

Correct Installation Method

 

The correct installation of single-row cylindrical roller bearings is essential to ensure their performance and extend their service life. The following are detailed installation steps and precautions:
 

Preparation: Install in a dry and clean environment. The processing quality of each component should be carefully checked before installation. All mating connection surfaces must be carefully cleaned and burrs removed, and the unprocessed surface of the casting must be free of sand13.
Cleaning and lubrication: Before installation, it should be cleaned with gasoline or kerosene, used after drying, and ensure good lubrication. The bearings are generally lubricated with grease, and oil lubrication can also be used.

Pressing the bearing: When the interference is small, the end face of the bearing ring can be pressed with a sleeve at room temperature, and the sleeve can be knocked with a hammer head, and the ring can be pressed in evenly through the sleeve. If installed in large quantities, a hydraulic press can be used. When pressing in, the outer ring end face and the housing shoulder end face, the inner ring end face and the shaft shoulder end face should be pressed tightly, and no gap is allowed.

Heating installation: When the interference is large, oil bath heating or inductor heating bearings can be used for installation. The heating temperature range is 80℃-100℃, and the maximum cannot exceed 120℃. At the same time, nuts or other appropriate methods should be used to tighten the bearings to prevent the bearings from shrinking in the width direction after cooling and causing a gap between the ring and the shoulder.

Rotation test: After installation, a rotation test should be carried out. First, the rotating shaft or bearing box should be used. If there is no abnormality, the power should be used for no-load and low-speed operation. Then, the rotation speed and load should be gradually increased according to the operation conditions, and the noise, vibration and temperature rise should be detected. If abnormalities are found, the operation should be stopped and checked. It can be delivered for use only after the operation test is normal.

By following the above steps and precautions, the problem of axis deviation of single-row cylindrical roller bearings during installation can be effectively avoided, thereby ensuring the normal operation of the bearings and extending their service life.

 

Hot Tags: available nu2968-m1 single-row cylindrical roller bearing, suppliers, agency, price, for sale, NUP2328 E M1 Bearing, NU2328 E M1A C4 Bearing

Send Inquiry